manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

D–19

Mouse does not respond to 
movement or is too slow. 
(continued)

Computer is in 

standby

 mode.

Press the power button to resume 
from 

standby

 mode.

Input is coming from a 
nearby wireless mouse.

1. Ensure that the mouse batteries 

are fresh.

2. Place the receiver over 30 cm 

(12 in) from a telephone, power 
supply, transformer, computer, 
other electrical device, or power 
cords or cables.

3. The receiver should not be 

placed on or inside of a metal 
surface.

Ä

CAUTION:

 When attempting to resume from 

standby

 mode, do not hold down the 

power button for more than four seconds. Otherwise, the computer will shut down and 
you will lose any unsaved data.

Mouse will only move 
vertically or horizontally, or 
movement is jerky.

Mouse roller ball is 
dirty.

Remove roller ball cover from the 
bottom of the mouse and clean it.

Solving Keyboard and Mouse Problems

Problem

Cause

Solution

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 709 General Information Manual preview
709
Brand: IBM Pages: 52
IBM NetVista A22p Kurzübersicht preview
NetVista A22p
Brand: IBM Pages: 78
IBM NetVista A22p Manual D'Utilisation preview
NetVista A22p
Brand: IBM Pages: 90
NEC SP B-Series Service And Reference Manual preview
SP B-Series
Brand: NEC Pages: 146
Advantech AIMB-T1217 Series User Manual preview
AIMB-T1217 Series
Brand: Advantech Pages: 32
DFI DT122-SB Installation Manual preview
DT122-SB
Brand: DFI Pages: 15
IBM 300PL (Dutch) Software Manual preview
300PL
Brand: IBM Pages: 40
Onyx MedPC-5500 Manual preview
MedPC-5500
Brand: Onyx Pages: 42
Baker Invivo2 300 UM-010 User Manual preview
Invivo2 300 UM-010
Brand: Baker Pages: 48
Vivo DESK-V111GT Instruction Manual preview
DESK-V111GT
Brand: Vivo Pages: 8
Dell Precision R5400 User Manual preview
Precision R5400
Brand: Dell Pages: 111
VS Cabling Sitting/Standing Workstation Assembly Instructions Manual preview
Cabling Sitting/Standing Workstation
Brand: VS Pages: 8
Kennmex K790 Series User Manual preview
K790 Series
Brand: Kennmex Pages: 40
Gispen IC HI Series Installation Manual preview
IC HI Series
Brand: Gispen Pages: 6
Shuttle XPC Barebone SA76G2 Specifications preview
XPC Barebone SA76G2
Brand: Shuttle Pages: 6
XMA Viglen Omnino Pro Assembly Manual preview
Viglen Omnino Pro
Brand: XMA Pages: 60
Fancom AURA 70 Manual preview
AURA 70
Brand: Fancom Pages: 29
UMAX Computer Corporation SuperMac C500 User Manual preview
SuperMac C500
Brand: UMAX Computer Corporation Pages: 113

Brands by name

Popular brands

Load more brands