HP Compaq dc5100 Series Service & Reference Manual Download Page 44 | Manualshive

Page: 44 / 230

background image

3–14

376220-001

Service Reference Guide, dc5100

Desktop Management

Pre-Boot Authorization

Allows you to enable/disable the Smart Card to be used in
place of the Power-On Password.

Smart Cover

Allows you to:

• Enable/disable the Cover Lock.
• Enable/disable the Cover Removal Sensor.

✎

Notify User

alerts the user that the sensor has detected that

the cover has been removed.

Setup Password

requires that

the setup password be entered to boot the computer if the
sensor detects that the cover has been removed.

This feature is supported on select models only. See the

Desktop Management Guide

on the

Documentation CD

for

more information.

Embedded Security

Allows you to:

• Enable/disable the Embedded Security device.
• Reset the device to Factory Settings.

This feature is supported on select models only.

See

HP ProtectTools Embedded Security Guide

, on the

Documentation CD

for more information.

Device Security

Enables/disables serial ports, parallel port, front USB ports,
system audio, network controllers (some models), MultiBay
devices (some models), and SCSI controllers (some models).

Network Service Boot

Enables/disables the computer’s ability to boot from an
operating system installed on a network server. (Feature
available on NIC models only; the network controller must
reside on the PCI bus or be embedded on the system board.)

System IDs

Allows you to set:

• Asset tag (18-byte identifier) and ownership Tag (80-byte

identifier displayed during POST).

See the

Desktop Management Guide

on the

Documentation CD

for more information.

• Chassis serial number or Universal Unique Identifier

(UUID) number. The UUID can only be updated if the
current chassis serial number is invalid. (These ID numbers
are normally set in the factory and are used to uniquely
identify the system.)

Keyboard locale setting (for example, English or German) for
System ID entry.

Computer Setup Utilities (F10) Security Features

(Continued)

Feature

Description

✎

For more information about Computer Setup, see the

Computer Setup (F10) Utility Guide

.

Support for security features may vary depending on your specific computer configuration.

«
...
42
43
44
45
46
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: FabiaTech Pages: 62

Brand: Acer Pages: 74

Brand: Acer Pages: 83

Brand: Acer Pages: 77

Brand: Acer Pages: 97

Brand: Acer Pages: 73

Brand: Acer Pages: 28

Brand: Acer Pages: 105

Brand: Acer Pages: 98

Brand: Acer Pages: 30

Brand: Acer Pages: 52

Brand: Acer Pages: 101

Brand: Acer Pages: 95

Aspire Timeline 4810T

Brand: Acer Pages: 148

Brand: Acer Pages: 127

Aspire V 15 Series

Brand: Acer Pages: 86

Brand: Acer Pages: 67

Brand: Acer Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands