manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

C–3

301-Keyboard Error

Keyboard failure.

Reconnect keyboard with computer 
turned off.
Check connector for bent or missing 
pins.
Ensure that none of the keys are 
depressed.
Replace keyboard.

303-Keyboard 
Controller Error

I/O board keyboard 
controller.

Reconnect keyboard with computer 
turned off.
Replace the system board.

304-Keyboard or 
System Unit Error

Keyboard failure.

Reconnect the keyboard with computer 
turned off.
Ensure that none of the keys are 
depressed.
Replace keyboard.
Replace system board. 

501-Display Adapter 
Failure

Graphics display 
controller.

Reseat the graphics card (if applicable).
Clear CMOS.
Verify that the monitor is attached and 
turned on.
Replace the graphics controller (if 
applicable).

510-Splash Screen 
image corrupted

Splash Screen image has 
errors.

Install latest version of ROMPaq to 
restore image.

511-CPU, CPUA, or 
CPUB Fan not detected

Fan is not connected or 
may have malfunctioned.

Reseat fan cable.
Reseat the fan.
Replace the fan.

512-Chassis, rear 
chassis, or front chassis 
fan not detected

Fan is not connected, 
may have malfunctioned.

Reseat chassis, rear chassis, or front 
chassis fan cable.
Reseat chassis, rear chassis, or front 
chassis fan.
Replace chassis, rear chassis, or front 
chassis fan.

514-CPU or Chassis 
Fan not detected.

CPU fan is not connected 
or may have 
malfunctioned.

Reseat CPU or chassis fan.
Reseat fan cable.
Replace CPU or chassis fan.

601-Diskette Controller 
Error

Diskette controller 
circuitry or floppy drive 
circuitry incorrect.

Run Computer Setup (F10 Setup).
Check and/or replace cables.
Clear CMOS.
Replace diskette drive. 
Replace the system board.

POST Error Messages 

Screen Message

Probable Cause

Recommended Action

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Acer Veriton 5800 Manuel D'Utilisation preview
Veriton 5800
Brand: Acer Pages: 106
Acer Veriton 2800 Manual Do Utilizador preview
Veriton 2800
Brand: Acer Pages: 83
Acer Veriton 2800 Guía Del Usuario preview
Veriton 2800
Brand: Acer Pages: 81
Acer Veriton 2800 Service Manual preview
Veriton 2800
Brand: Acer Pages: 89
Acer T230H - Bmidh Wide Touch Screen Display Buyer'S Manual preview
T230H - Bmidh Wide Touch Screen Display
Brand: Acer Pages: 12
Acer Veriton 6800 User Manual preview
Veriton 6800
Brand: Acer Pages: 100
3M Staff Workstation 795 Quick Start Manual preview
Staff Workstation 795
Brand: 3M Pages: 6
3M Dynapro ET 3200 Series Field Wiring Manual preview
Dynapro ET 3200 Series
Brand: 3M Pages: 21
7starlake ROC254A User Manual preview
ROC254A
Brand: 7starlake Pages: 8
IBM Aptiva Series Handbook preview
Aptiva Series
Brand: IBM Pages: 164
IBM 6219 - IntelliStation M - Pro Hardware Maintenance Manual preview
6219 - IntelliStation M - Pro
Brand: IBM Pages: 154
IBM NetVista Technical Information Manual preview
NetVista
Brand: IBM Pages: 72
IBM IntelliStation M Pro Type 6868 User Manual preview
IntelliStation M Pro Type 6868
Brand: IBM Pages: 188
ZIEHL-ABEGG UNIcon Operating Instructions Manual preview
UNIcon
Brand: ZIEHL-ABEGG Pages: 84
Büttner Elektronik MT iQ Basic Instruction Manual preview
MT iQ Basic
Brand: Büttner Elektronik Pages: 36
Oracle MICROS Compact Workstation 310 Quick Assembly Manual preview
MICROS Compact Workstation 310
Brand: Oracle Pages: 2
Vivo DESK V001G Instruction Manual preview
DESK V001G
Brand: Vivo Pages: 2
Arista AP-3500-E01 User Manual preview
AP-3500-E01
Brand: Arista Pages: 47

Brands by name

Popular brands

Load more brands