HP Compaq dc5100 Series Service & Reference Manual Download Page 139

Page: 139 / 230

Service Reference Guide, dc5100

376220-001

7–27

Removal and Replacement Procedures— Small Form Factor (SFF) Chassis

7. Disconnect the power cable

and data cable

from the back of the hard drive.

8. Pull the tab that locks the drive in place away from the drive

, slide the hard drive toward

the front of the computer, then lift it up and out of the bay

To install a hard drive, reverse the above procedure.

✎

The replacement hard drive kit includes several data cables. Make sure to use the cable that is
exactly the same as the factory-installed cable.

✎

If the system has only one SATA hard drive, the data cable must be connected to the

blue

connector labeled P60 SATA 0 first to avoid any hard drive performance problems.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands