HP Compaq dc5100 Series Service & Reference Manual Download Page 192 | Manualshive

Page: 192 / 230

background image

D–8

376220-001

Service Reference Guide, dc5100

Solving Hard Drive Problems

Solving Hard Drive Problems

Problem

Cause

Solution

Hard drive error occurs.

Hard disk has bad
sectors or has failed.

Use a utility to locate and block
usage of bad sectors. If necessary,
reformat the hard disk.
In Windows XP, right-click

Start

,

click

Explore

, and select a drive.

Select

File > Properties > Tools

.

Under

Error-checking

, click

Check Now

.

Disk transaction problem.

Either the directory
structure is bad or there
is a problem with a file.

In Windows XP, right-click

Start

,

click

Explore

, and select a drive.

Select

File > Properties > Tools

.

Under

Error-checking

, click

Check Now

.

Drive not found (identified).

Loose cable.

Check cable connections.

The system may not
have automatically
recognized a newly
installed device.

1. Run Computer Setup.

2. If the system still does not

recognize the new device,
check to see if the device is
listed within Computer Setup. If
it is listed, the probable cause is
a driver problem. If it is not
listed, the probable cause is a
hardware problem.

3. If this is a newly installed drive,

enter Setup and try adding a
POST delay under

Advanced

> Power-On

.

Drive jumper settings
may be incorrect.

If the drive is a secondary drive that
has just been installed on the same
cable as the primary drive, verify
that the jumpers for both drives are
set correctly.

Drive’s IDE (ATA)
controller is disabled in
Computer Setup.

Run Computer Setup and enable the
Primary and Secondary IDE (ATA)
controllers in

Storage > Storage

Options

.

Drive responds slowly
immediately after
power-up.

Run Computer Setup and increase
the POST Delay in

Advanced >

Power-On Options

.

Nonsystem disk/NTLDR
missing message.

System is trying to start
from a non bootable
diskette or USB device.

Remove the media from the drive.

«
...
190
191
192
193
194
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

SmartCraft SC5000

Brand: Mercury Pages: 64

Brand: Gateway Pages: 164

Brand: Gigabyte Pages: 34

Brand: Radio Shack Pages: 276

Brand: Vivo Pages: 8

Brand: Acer Pages: 120

Brand: Display Mount Pro Pages: 6

Brand: CELLmatic Pages: 51

Presario Notebook PC

Brand: Compaq Pages: 1

Presario CQ3300 - Desktop PC

Brand: Compaq Pages: 1

Brand: Compaq Pages: 2

Deskpro Workstation AP230

Brand: Compaq Pages: 31

Deskpro EN Series

Brand: Compaq Pages: 53

dc7800 - Convertible Minitower PC

Brand: Compaq Pages: 4

Deskpro 4000S - Desktop PC

Brand: Compaq Pages: 142

Brand: ClearCube Pages: 4

Brand: AOpen Pages: 1

Brand: AOpen Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands