HP Compaq dc5100 Series Service & Reference Manual Download Page 38 | Manualshive

Page: 38 / 230

background image

3–8

376220-001

Service Reference Guide, dc5100

Desktop Management

8. Download a BIOS utility for replicating setup (repset.exe) and copy it onto the configuration

diskette or USB flash media device. To obtain this utility, go to

h ttp://welcome.hp.com/support/files

and enter the model number of the computer.

9. On the configuration diskette or USB flash media device, create an autoexec.bat file

containing the following command:

repset.exe

10. Turn off the computer to be configured. Insert the configuration diskette or USB flash media

device and turn the computer on. The configuration utility will run automatically.

11. Restart the computer when the configuration is complete.

Creating a Bootable Device

Supported USB Flash Media Device

Supported devices, such as an HP Drive Key or a DiskOnKey, have a preinstalled image to
simplify the process of making them bootable. If the USB flash media device being used does not
have this image, use the procedure later in this section (see

“Unsupported USB Flash Media

Device” on page 10

Ä

CAUTION:

Not all computers can be booted from a USB flash media device. If the default boot order in

the Computer Setup (F10) Utility lists the USB device before the hard drive, the computer can be booted
from a USB flash media device. Otherwise, a bootable diskette must be used.

To create a bootable USB flash media device, you must have:

■

One of the following systems:

❏

HP Compaq Business Desktop dc7100 series

❏

HP Compaq Business Desktop dx6100 series

❏

HP Compaq Business Desktop d530 Series - Ultra-Slim Desktop, Small Form Factor, or
Convertible Minitower

❏

Compaq Evo D510 Ultra-slim Desktop

❏

Compaq Evo D510 Convertible Minitower/Small Form Factor

Depending on the individual BIOS, future systems may also support booting to a USB flash
media device.

Ä

CAUTION:

If you are using a computer other than one named above, make sure the default boot order

in the Computer Setup (F10) Utility lists the USB device before the hard drive.

■

One of the following storage modules:

❏

16MB HP Drive Key

❏

32MB HP Drive Key

❏

32MB DiskOnKey

❏

64MB HP Drive Key

❏

64MB DiskOnKey

❏

128MB HP Drive Key

❏

128MB DiskOnKey

«
...
36
37
38
39
40
...
»

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Brand: Acer Pages: 102

Brand: Acer Pages: 118

DeviceEdge Mini AIE-C011

Brand: Aetina Pages: 14

Brand: Aaeon Pages: 90

BOXER-64 Series

Brand: Aaeon Pages: 90

Brand: Advantech Pages: 68

Brand: Warner Communications Pages: 50

BX-951-DC series

Brand: Contec Pages: 111

Brand: VS Pages: 20

Brand: Element 14 Pages: 17

Brand: DFI Pages: 4

Brand: CELLmatic Pages: 51

Brand: Gigabyte Pages: 64

Brand: AKG Pages: 32

H6 i-One Series

Brand: Cybernet Pages: 30

Allen-Bradley 6181F-12TPWE

Brand: Rockwell Automation Pages: 28

Allen-Bradley 6181X

Brand: Rockwell Automation Pages: 32

Brand: Packard Bell Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands