HP Compaq dc5100 Series Service & Reference Manual Download Page 191

Page: 191 / 230

Service Reference Guide, dc5100

376220-001

D–7

Cannot format diskette.
(continued)

Diskette is
write-protected.

Use another diskette or remove the
write protection.

Diskette write control is
enabled.

Use Computer Setup to check the
storage security feature disabled
settings.

A problem has occurred
with a disk transaction.

The directory structure is
bad, or there is a
problem with a file.

In Windows XP, right-click

Start

click

Explore

, and select a drive.

Select File > Properties >
Tools

Under

Error-checking

click

Check Now

Diskette drive cannot read
a diskette.

Diskette is not
formatted.

Format the diskette.

You are using the wrong
diskette type for the
drive type.

Check the type of drive that you
are using and use the correct
diskette type.

You are reading the
wrong drive.

Check the drive letter in the path
statement.

Diskette is damaged.

Replace the diskette with a new one.

“Invalid system disk”
message is displayed.

A diskette that does not
contain the system files
needed to start the
computer has been
inserted in the drive.

When drive activity stops, remove
the diskette and press the

Spacebar

. The computer should

start up.

Diskette error has
occurred.

Restart the computer by pressing the
power

button.

Cannot Boot to Diskette.

Diskette is not bootable.

Replace with a bootable diskette.

Diskette boot has been
disabled in Computer
Setup.

Run Computer Setup and enable
diskette boot in

Storage > Boot

Order

Run Computer Setup and enable
Removable Media Boot in

Storage > Storage Options >
Removable Media Boot

✎

Both steps should be used as
the

Removable Media

Boot

function overrides the

Boot Order

enable

command.

Removable media boot
has been disabled in
Computer Setup.

Run Computer Setup and enable
Removable Media Boot in

Storage > Storage Options>
Removable Media Boot

Network server mode is
enabled in Computer
Setup.

Run Computer Setup and disable

Network Server Mode

Security > Password Options

Solving Diskette Problems

(Continued)

Problem

Cause

Solution

Summary of Contents for Compaq dc5100 Series







































































































































































































































Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands

HP Compaq dc5100 Series, Service & Reference Manual

Search results

Summary of Contents for Compaq dc5100 Series

Reviews:

Related manuals for Compaq dc5100 Series

Brands by name

Popular brands