manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

6–20

376220-001

Service Reference Guide, dc5100

Removal and Replacement Procedures— Microtower (MT) Chassis

6.10 Chassis Fan 

1. Prepare the computer for disassembly (

Section 6.1, “Preparation for Disassembly”

).

2. Remove the access panel and rotate the computer so the system board is parallel to the table 

to make it easier to work on (

Section 6.3, “Access Panel”

).

3. Disconnect the power cable that connects the chassis fan to the system board 

1

.

4. Remove the four screws from the rear of the chassis 

2

 that secure the fan. 

5. Remove the fan from the chassis 

3

.

To install the chassis fan, reverse the removal procedure.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Ohio Scientific 500 Instructions Manual preview
500
Brand: Ohio Scientific Pages: 43
IBM Personal Computer Referencia Rápida preview
Personal Computer
Brand: IBM Pages: 64
EAI 580 Reference Handbook preview
580
Brand: EAI Pages: 132
Gateway E-3600 System Manual preview
E-3600
Brand: Gateway Pages: 158
M5Stack POECAM Manual preview
POECAM
Brand: M5Stack Pages: 15
Avid Technology Dell T7600 Configuration Manuallines preview
Dell T7600
Brand: Avid Technology Pages: 23
I-Tech Digital Signage LCD integrated w/ PC... Specifications preview
Digital Signage LCD integrated w/ PC...
Brand: I-Tech Pages: 1
Zotac ZBOX NANO User Manual preview
ZBOX NANO
Brand: Zotac Pages: 20
Neousys Technology Nuvo-8108GC Series User Manual preview
Nuvo-8108GC Series
Brand: Neousys Technology Pages: 142
Yamaha CX5M Owner'S Manual preview
CX5M
Brand: Yamaha Pages: 65
Yamaha CX5MII Owner'S Manual preview
CX5MII
Brand: Yamaha Pages: 72
Yamaha C1 Operating Manual preview
C1
Brand: Yamaha Pages: 78
Yamaha AW2816 Service Manual preview
AW2816
Brand: Yamaha Pages: 120
Yamaha AW2816 Owner'S Manual preview
AW2816
Brand: Yamaha Pages: 420
HP MT EU Business PC Illustrated Parts & Service Map preview
MT EU Business PC
Brand: HP Pages: 3
HP ms6005 Specifications preview
ms6005
Brand: HP Pages: 2
HP m9260f Pavilion Elite Setup Poster preview
m9260f Pavilion Elite
Brand: HP Pages: 1
HP M9402f - pavilion - elite Specifications preview
M9402f - pavilion - elite
Brand: HP Pages: 2

Brands by name

Popular brands

Load more brands