manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

6–21

Removal and Replacement Procedures— Microtower (MT) Chassis

6.11  Front I/O Panel Housing Assembly 

1. Prepare the computer for disassembly (

Section 6.1, “Preparation for Disassembly”

).

2. Remove the access panel and rotate the computer so the system board is parallel to the table 

to make it easier to work on (

Section 6.3, “Access Panel”

).

3. Disconnect three attaching cables from the system board: the power switch/LED cable, the 

front USB cable, and the front audio cable.

4. Remove the two screws 

1

 that secure the housing to the chassis and then pull the housing 

2

 

away from the chassis.

To install the housing assembly, reverse the removal procedures.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

IBM 5150 Hardware Reference Manual preview
5150
Brand: IBM Pages: 393
IBM PC 300 Brukerhåndbok preview
PC 300
Brand: IBM Pages: 198
IBM NetVista X40 Oprogramowanie Manual preview
NetVista X40
Brand: IBM Pages: 32
IBM NetVista X40 Om Programvaren Manual preview
NetVista X40
Brand: IBM Pages: 32
IBM NetVista X40 Datorns Förinstallerade Program Manual preview
NetVista X40
Brand: IBM Pages: 32
IBM NetVista X40 Hurtigreferanse Manual preview
NetVista X40
Brand: IBM Pages: 46
IBM PC 300 Om De Forudinstallerede Programmer Manual preview
PC 300
Brand: IBM Pages: 32
IBM NetVista A30 Manual De Consulta Rápida preview
NetVista A30
Brand: IBM Pages: 72
Advantech USC-250 User Manual preview
USC-250
Brand: Advantech Pages: 50
IEI Technology FLEX-BX100-ULT5 User Manual preview
FLEX-BX100-ULT5
Brand: IEI Technology Pages: 121
Rockler Adjustable Height Workstation Assembly Instructions Manual preview
Adjustable Height Workstation
Brand: Rockler Pages: 8
S&T Kontron KBox E-410-APL User Manual preview
Kontron KBox E-410-APL
Brand: S&T Pages: 78
Biostar IDEQ 200T User Manual preview
IDEQ 200T
Brand: Biostar Pages: 60
IBASE Technology CSB200-898 User Manual preview
CSB200-898
Brand: IBASE Technology Pages: 87
BE QUIET! Dark Base 700 User Manual preview
Dark Base 700
Brand: BE QUIET! Pages: 48
IBM Aptiva 2165 Hardware Maintenance Service preview
Aptiva 2165
Brand: IBM Pages: 167
MiTAC E - 8188 Service Manual preview
E - 8188
Brand: MiTAC Pages: 246
Compaq d260 - Microtower Desktop PC Illustrated Parts Map preview
d260 - Microtower Desktop PC
Brand: Compaq Pages: 1

Brands by name

Popular brands

Load more brands