manualshive.com logo in svg

HP Compaq dc5100 Series, Service & Reference Manual

The HP Compaq dc5100 Series is a versatile desktop computer designed for performance and productivity. Ensure seamless troubleshooting and maintenance with the comprehensive "Service & Reference Manual". Download this essential manual for free from our website to maximize your experience with this powerful computing solution.

Share
Download
background image

Service Reference Guide, dc5100

376220-001

6–27

Removal and Replacement Procedures— Microtower (MT) Chassis

6.16 System Board 

1. Prepare the computer for disassembly (

Section 6.1, “Preparation for Disassembly”

).

2. Remove the access panel and rotate the computer so the system board is parallel to the table 

to make it easier to work on (

Section 6.3, “Access Panel”

).

3. Remove all PCI expansion boards (

Section 6.7.2, “PCI Expansion Card”

).

4. Disconnect all cables connected to the system board, noting their location for reinstallation.

5. Remove the 3-1/4” drives from the drive cage to make it easier to handle the system board.

6. Remove the eight screws that secure the system board to the chassis 

1

 then, slide the system 

board towards the front of the chassis 

2

 to remove it.

To install the system board, reverse the removal procedures.

Summary of Contents for Compaq dc5100 Series







































































































































































































































Reviews:

No comments

Related manuals for Compaq dc5100 Series

Layher 3201 Instructions For Assembly And Use preview
3201
Brand: Layher Pages: 6
EUROCOM LP295 Quick Manual preview
LP295
Brand: EUROCOM Pages: 1
Gateway E-3600 System Manual preview
E-3600
Brand: Gateway Pages: 158
PMC MicroMate -101 User Manual preview
MicroMate -101
Brand: PMC Pages: 126
A1Touch AOD 170 User Manual preview
AOD 170
Brand: A1Touch Pages: 8
Vivo DESK-V000W Instruction Manual preview
DESK-V000W
Brand: Vivo Pages: 3
Genesis Titan 750 Quick Installation Manual preview
Titan 750
Brand: Genesis Pages: 14
Dell Inspiron 3470 Owner'S Manual preview
Inspiron 3470
Brand: Dell Pages: 51
Dell INSPIRON Inspiron 1100 Owner'S Manual preview
INSPIRON Inspiron 1100
Brand: Dell Pages: 95
Dell Inspiron 24-5400 Setup And Specifications preview
Inspiron 24-5400
Brand: Dell Pages: 26
Dell Inspiron 3472 Setup And Specifications preview
Inspiron 3472
Brand: Dell Pages: 20
Asus TW100-E6 Configuration Manual preview
TW100-E6
Brand: Asus Pages: 18
Asus TW300-E5/PI4 User Manual preview
TW300-E5/PI4
Brand: Asus Pages: 174
Asus TS700-E6/RS8 User Manual preview
TS700-E6/RS8
Brand: Asus Pages: 166
Toshiba Satellite A70 User Manual preview
Satellite A70
Brand: Toshiba Pages: 217
Toshiba Satellite A100 Series Maintenance Manual preview
Satellite A100 Series
Brand: Toshiba Pages: 294
Toshiba Satellite A300 Series Maintenance Manual preview
Satellite A300 Series
Brand: Toshiba Pages: 263
Toshiba Satellite A20 Series Maintenance Manual preview
Satellite A20 Series
Brand: Toshiba Pages: 495

Brands by name

Popular brands

Load more brands