HP 64783A User Manual Download Page 66 | Manualshive

Page: 66 / 816

background image

Step 19: Prepare the deMMUer so you can see
symbolic addresses in the trace list

•

Choose Settings

→

DeMMUer

→

, and then make sure the Verbose pushbutton is

pressed (to see details on screen). Choose Settings

→

DeMMUer

→

Load from

Memory.

•

Or, using the command line, enter the following command:

load demmuer verbose

A display similar to the following should appear.

All physical addresses within the following 32-Mbyte range(s) will be
reverse translated into logical addresses for the analyzer:
000000000..001ffffff@a
0fe000000..0ffffffff@a

The lowest logical address from the translation tables is assumed when
multiple translations reference the same physical address.

The above command loaded the deMMUer with information to reverse translate
two ranges of physical addresses obtained from the MMU. By default, the
deMMUer was enabled when it was loaded. The verbose mode of this command
was selected so we could see which ranges of physical addresses would be reverse
translated by the deMMUer.

Any physical addresses that might have been derived from two or more logical
addresses will be reverse translated to the lowest logical address by the deMMUer.

Remember the setup of the MMU. It showed the following:

Logical Address Physical Address Attributes
000000000..000007fff 000000000..000007fff@a S W
000008000..00000ffff 000008000..00000ffff@a W
000010000..000017fff 0ffff0000..0ffff7fff@a W
000018000..00001bfff 0ffff8000..0ffffbfff@a
00001c000..00001ffff 0ffffc000..0ffffffff@a S
0ff000000..0ffffffff 0ff000000..0ffffffff@a TT

Physical address ffff0000H, for example, might appear when the MMU translates
either logical address 10000H or logical address ffff0000H. The deMMUer will
send 10000H to the analyzer because it is the lowest logical address that might have
caused physical address ffff0000H to appear on the emulation bus.

Chapter 1: Getting Started
Step 19: Prepare the deMMUer so you can see symbolic addresses in the trace list

36

«
...
64
65
66
67
68
...
»

Summary of Contents for 64783A

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 64783A

Brand: Yamaha Pages: 69

Brand: Parr Instrument Company Pages: 130

Brand: jenway Pages: 17

Vigilant ELM Series

Brand: Eagle Eye Power Solutions Pages: 9

Brand: Daewoo Pages: 2

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Brand: ICS Schneider Messtechnik Pages: 40

Brand: Barksdale Pages: 2

Brand: Dräger Pages: 538

Brand: Lutron Electronics Pages: 13

Brand: Cal Test Electronics Pages: 12

Brand: Reed Instruments Pages: 14

Brand: POSEIDON Pages: 13

Brand: B meters Pages: 3

Brand: Oceanic Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands