HP 64783A User Manual Download Page 494 | Manualshive

Page: 494 / 816

background image

data

This specifies that the expression that follows is a data value on the emulation
processor data bus.

—EXPR—

An expression is a combination of numeric values, symbols, operators, and
parentheses, specifying an address, data, or status value. See the EXPR syntax
diagram.

long_aligned

Causes a mask to be applied to the address to force it to a long word boundary
(least significant hex digit is 0, 4, 8, or C). This is necessary because the
emulation-bus analyzer may not otherwise see the address on the address bus due to
the way the processor fetches instructions.

not

This specifies that the analyzer search for the logical “not” of the specified range or
state, that is addresses not in the specified range or an address not in the specified
state.

or

This option allows you to specify multiple states to be captured during a trace
measurement.

range

This indicates a range of addresses to be specified (—EXPR— thru —EXPR—).

status

This specifies that the expression following, or status word, is a status value for the
processor.

<STATUS>

This prompts you to enter a status value in the command line. Status values can be
entered from softkeys or typed into the keyboard. Numeric values may be include
symbols, operators, and parentheses. See the EXPR syntax diagram. Refer to
Chapter 5, "Using the Emulation-Bus Analyzer", for a list of predefined status
equates that cover common processor operations.

Chapter 11: Emulator Commands
QUALIFIER

464

«
...
492
493
494
495
496
...
»

Summary of Contents for 64783A

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 64783A

Brand: Valor Pages: 13

Brand: Campbell Pages: 31

MIC TRAC MT-3000

Brand: GAGEMAKER Pages: 20

Goldmann AT 870

Brand: Haag-Streit Pages: 20

Signet FlowtraMag 2580 Series

Brand: GF Pages: 20

Brand: Ocea Soft Pages: 19

Frontline 802.11

Brand: Teledyne Lecroy Pages: 223

Brand: Clavitech Pages: 56

Brand: FASAR ELETTRONICA Pages: 2

Brand: Water I.D. Pages: 56

Brand: Meec tools Pages: 23

NetSure M832DNA

Brand: Vertiv Pages: 176

Brand: Alpes Lasers Pages: 41

Brand: Thermo Scientific Pages: 56

Brand: Velleman Pages: 15

Brand: sewerin Pages: 80

Brand: YOKOGAWA Pages: 63

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands