HP 64783A User Manual Download Page 467 | Manualshive

Page: 467 / 816

background image

low_word

Causes inverse assembly to begin with the opcode stored in the low word of the
long word at the specified trace memory line number.

mnemonic

Lists trace information with opcodes in mnemonic format.

offset_by

This option allows you to offset the listed address value from the address of the
instruction. By subtracting the offset value from the physical address of the
instruction, the system makes the listed address match that given in the assembler
or compiler listing.

This option is also useful for displaying symbols and source lines in dynamically
relocated programs.

Note that when using the set source only command, the analyzer may operate more
slowly than when using the set source on command. This is an operating
characteristic of the analyzer:

When you use the command set source on, and are executing only assembly
language code (not high-level language code), no source lines are displayed.
The trace list will fill immediately with the captured assembly language
instructions.

When using set source only, no inverse assembled code is displayed.
Therefore, the emulation software will try to fill the display with high-level
source code. This requires the emulation software to search for any captured
analysis data generated by a high-level language statement.

In conclusion, you should not set the trace list to set source only when tracing
assembly code. This will result in optimum analyzer performance.

status

binary

Lists absolute status information in binary form.

hex

Lists absolute status information in hexadecimal form.

mnemonic

Lists absolute status information in mnemonic form.

Chapter 11: Emulator Commands

DISPLAY TRACE

437

«
...
465
466
467
468
469
...
»

Summary of Contents for 64783A

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 64783A

Brand: Bacharach Pages: 64

Brand: VeEX Pages: 842

Brand: VEE GEE Pages: 2

Brand: Aethra Pages: 2

Brand: Flymaster Pages: 7

Brand: Kipp & Zonen Pages: 32

Brand: Z-TRAUQ Pages: 10

Brand: Ziton Pages: 2

Brand: novomatics Pages: 39

Brand: A&D Pages: 8

Brand: C. B. Gitty Crafter Supply Pages: 12

Brand: AEMC instruments Pages: 4

Brand: Keysight Technologies Pages: 104

Nova-Pro IR 850

Brand: MONARCH INSTRUMENT Pages: 36

Brand: Würth Pages: 188

Brand: Chauvin Arnoux Pages: 104

Brand: Obdstar Pages: 16

IBIZA400RGB 15-1567

Brand: Ibiza Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands