manualshive.com logo in svg

GRASS VALLEY IQUCP25, User Manual

Introducing the GRASS VALLEY IQUCP25, a versatile broadcasting equipment built to enhance your production experience. This user-friendly device requires a reliable User Manual for optimized usage. Download the comprehensive manual for free on manualshive.com to unlock the full potential of your GRASS VALLEY IQUCP25 and achieve seamless broadcasting excellence.

Share
Download
background image

29

UCP

-

3901

User Manual

DIAG status LED

Shows the following states:

•

Green:

 PTP-LOCK OK.

•

Off:

 PTP-LOCK Fail.

See also 

Time Sync Configuration

, on page 85 and 

Logging - System

, 

on page 140 for more information.

BOARD status LED Shows the following states:

•

Green: 

PTP-SYNC OK. PTP being used and clocks are within the 

accepted range.

•

Off: 

PTP-SYNC Fail. PTP being used but clocks haven't 

synchronized /- 1mS.

PTP status LED

Future use.

CPU status LED

Future use.

REF status LED

Shows the following state:

•

Flashing Green:

 Watchdog timer OK.

Densité status LED Shows the following states (status indication priority

a

):

•

Red

 (level 6): Card is powering up. 

If solid red persists (>6 seconds), a hardware failure has been 

detected: the card’s CPU could not boot. This may be the result of 

the UCP

-

3901 Card not being equipped with its Micro-SD card or 

the Micro-SD card is not properly inserted. See 

Replacing the 

Micro-SD Card

, on page 324. 

•

Yellow

 (level 2): Card is booting.

•

Green

 (level 1): Card has finished booting. Normal operation.

•

Flashing Yellow

 (level 5): Card has been selected for local control 

using the Densité frame’s control panel by having pressed the 

card’s 

SELECT

 button. Press the card’s 

SELECT

 button again to 

remove local control.

•

Alternating Red / Green

 (level 4): Card’s firmware is being 

upgraded.

•

Flashing Red

 (level 3): Indicates one of the following possible 

errors:

• The presence of the rear panel has not been detected.

• Ensure the card is inserted into the correct Densité frame 

slot that lines-up with the rear panel.

• Ensure the rear panel is installed. See 

Installation of the 

Rear Connector Panel and Card

, on page 31.

• Fan Error: the card’s fan is not spinning, or is spinning too 

slowly, or the fan cable is disconnected. Urgent maintenance 

procedures must be considered: If this alarm has been raised, 

the fan on the UCP

-

3901 Card may have to be replaced. See 

Cooling Fan Operational Assessment

, on page 320.

Item

Description

Summary of Contents for IQUCP25



















































































































































































































































































































































Reviews:

No comments

Related manuals for IQUCP25

D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Brand: D-Link Pages: 4
Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Brand: Quantum Pages: 20
Amperes iPX5500 Instruction Manual preview
iPX5500
Brand: Amperes Pages: 8
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
Rolls HR11C Owner'S Manual preview
HR11C
Brand: Rolls Pages: 2
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Brand: IAR SYSTEMS Pages: 8
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
Rainbow QPBB Instruction Manual preview
QPBB
Brand: Rainbow Pages: 2
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
Intel 500 - DATASHEET REV 003 Datasheet preview
500 - DATASHEET REV 003
Brand: Intel Pages: 67
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
ADTRAN 1202052L1 User Manual preview
1202052L1
Brand: ADTRAN Pages: 136

Brands by name

Popular brands

Load more brands