GRASS VALLEY IQUCP25 User Manual Download | Manualshive

Page: 96 / 338

background image

96

Essence Processing SDC

NMOS

NMOS

The

NMOS

page allows various NMOS parameters to be set, allowing the UCP

-

3901 /

IQUCP25 / IQUCP50 to inter-operate with other equipment through an NMOS registry.
UCP

-

3901 / IQUCP25 / IQUCP50 supports Networked Media Open Specifications (NMOS)

AMWA IS-04 for device discovery and registration and IS-05 for connection management.

Furthermore, it supports AMWA BCP-002 recommendations for Grouping NMOS Resources.
UCP

-

3901 / IQUCP25 / IQUCP50 relies on an external NMOS registry that is used to register

NMOS devices.
PREREQUISITE:

• A working NMOS registry service must be available on the network.
• Entries for your NMOS registries have been added to the network DNS server. This

enables automatic DNS-SD discovery. Contact your IT department to do so. Otherwise

you can manually specify the registry to connect to.

Fig. 6-10: NMOS Page

«
...
94
95
96
97
98
...
»

Summary of Contents for IQUCP25



















































































































































































































































































































































Reviews:

No comments

Related manuals for IQUCP25

Brand: Ebyte Pages: 8

Brand: Qualys Pages: 2

Brand: Salto Pages: 2

Brand: mikroElektronika Pages: 3

Power Control Processor

Brand: ETC Pages: 64

Core 2 Quad Q9400

Brand: Intel Pages: 2

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: Omron Pages: 13

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Ubiquiti Pages: 13

VIGI NVR1004H-4P

Brand: TP-Link Pages: 2

Brand: Doremi Pages: 15

Brand: IBM Pages: 130

Brand: M-system Pages: 4

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

Brand: ETAS Pages: 68

Brand: Microcomputer Systems Pages: 21

Brand: Renesas Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands