GRASS VALLEY IQUCP25 User Manual Download

Page: 198 / 338

198

MADI Processing SDC

Ethernet RTP Receiver Audio Stats

Ethernet RTP Receiver Audio Stats

The

Ethernet RTP Receiver Audio Stats

page displays information on the RTP data

received on network interfaces 1 and 2 on a spigot-by-spigot basis. Units are megabits per

second.

Figure 7 - 12:

Ethernet RTP Receiver Audio Stats Page

Parameter

Description

Enable Stats

Set to display values.

Clear ETH 1 RTP

Counts
Clear ETH 2 RTP

Counts

Click to zero RTP Discontinuity counters for each Ethernet input.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands