GRASS VALLEY IQUCP25 User Manual Download

Page: 304 / 338

304

Multiviewer SDC

TSL

TSL

The

TSL

template allows you to select settings related to Multiviewer SDC support of the

TSL protocol.

Fig. 9-10: TSL Template

TSL protocol is supported in TSL Server Mode or TSL Client Mode, see

TSL Support

, on

page 268.
For two types of Ethernet protocols (UDP and TCP), you can separately set up IP address and

network port information.

Table 9-2: TSL Mode Settings

Setting

Description

UDP:
3.1 Port

Enter the IP port to receive TSL 3.1 messages on.

5.0 Port

Enter the IP port to receive TSL 5.0 messages on.

Mode

Select “Server”, or “Disabled”.

TCP:
IP Address

For

Server

Mode

Enter the local IP address of the Multiviewer SDC to be used for TSL

messages.
For

Client

Mode

Enter the IP address of the remote TSL Controller in the system.

3.1 Port

Enter IP port to receive TSL 3.1 messages on.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands