GRASS VALLEY IQUCP25 User Manual Download

Page: 268 / 338

268

Getting Started with the Multiviewer

TSL Support

TSL Support

TSL Protocol Tally Settings

TSL protocols are used widely throughout the industry for communication between a TSL

Tally controller and Under Monitor Displays (UMDs). The protocol enables tally lamp control

and text label data to be carried to each UMD device.
A TSL Tally controller handles the tally data in a video system and provides TSL Tally control

information to each UMD. The Multiviewer SDC supports two TSL protocols: TSL 3.1 and TSL

5.0. Initial TSL support settings are described here.
Setting up the multiviewer to work with a TSL tally-based system involves the following

steps:

• Specify how the multiviewer gets the TSL Tally message information.

See

Specifying Multiviewer TSL Tally Mode

, on page 268.

• Specify index parameters for each UMD on the video wall.

See

Specifying Index Parameters for each UMD

, on page 269.

Specifying Multiviewer TSL Tally Mode

The multiviewer may get its TSL Tally information in one of two modes:

•

Server Mode

- Multiviewer SDC listens for Tally messages.

Specify the Multiviewer SDC IP address and network port to receive Tally messages on.

•

Client Mode

- Multiviewer SDC reads Tally messages from a Tally controller.

Specify the IP address and network port number of the Tally controller.

Fig. 8-21: TSL Protocol Operating Modes

The RollCall Control Panel application is used to configure the TSL screen settings. See

RollCall

Layout

, on page 302.

UCP-3901

Multivewer

SDC

UCP-3901

Multivewer

SDC

IP Address, Port

TALLY CONTROLLER

IP Address, Port

Controller

Sends Out

Messages

Module Listens

Module Actively

Reads Information

a) Server Mode

b) Client Mode

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands