GRASS VALLEY IQUCP25 User Manual Download

Page: 128 / 338

128

Essence Processing SDC

Output Spigots

Parameter

Description

Spigot pane

The

Spigot

pane provides basic configuration for the selected Spigot.

Click

Take

to apply any changes made in this pane.

Direction

Displays spigot direction.

Input:

This spigot is a sender. See

Input Spigots

on page 122 for this

mode of operation.

Output:

This spigot is a receiver.

BNC

Associated HD-BNC connector on the rear panel. See also:

• For the UCP

3901:

12G/3G/HD/SD-SDI I/O – Serial digital video

inputs / outputs (4)

on page 34 and

3G / HD / SD SDI I/O – Serial

digital video inputs / outputs (12)

on page 35.

• For the IQUCP25 / IQUCP50:

Images of Rear Panel Connectors

page 46.

Status

Current spigot’s status.

: signal good.

FAIL

: signal not detected.

WARN: TPG:

a test pattern is being shown.

Last Spigot Take

The last

Take

performed on the spigot and how it was made.

RC:

RollCall; operation from a control panel or by an external agent,

like VSM.

IPCtrl:

GV Orbit.

RCStart:

The default at module startup.

Streaming

Set the Ethernet connectors to use for this spigot. This will also

determine the bandwidth to be used. Options are:

Dual:

Full redundancy to support SMPTE ST 2022-7, both Primary

(

SFP1

) and Secondary (

SFP2

) Ethernet connectors are used. All

bandwidth of both Ethernet connectors are used. See

Cabling to

Support SMPTE ST 2022

on page 55.

To support redundancy, you must set the

Flow Type

to 2110 for both

the primary and secondary ports for the Video, Audio, and Metadata

essences. See below.

Single:

use either Ethernet connector (

SFP1

SFP2

), and so half of

the available bandwidth.

Primary (

SFP1

) Ethernet connector only, and so half of the available

bandwidth.

Secondary (

SFP2

) Ethernet connector only, and so half of the

available bandwidth.
See

Rear Panel and Connectors

on page 32 for SFP / connector

locations.

Format

Select the format to be used on this spigot. This will ensure that the

appropriate level of bandwidth is allocated for the stream.

Receiver / Video

Std

Select the standard for the incoming video, or set to

Auto

to detect

the standard automatically.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands