GRASS VALLEY IQUCP25 User Manual Download

Page: 43 / 338

UCP

3901

User Manual

For further information about how to troubleshoot an issue, see

Troubleshooting

, on

page 325.
All alarms and operational statuses can also be seen from Rollcall Logging pages. These

pages provide the live status of the card. Theses statuses are also logged when using a Log

Server. See

Logging Pages

, on page 137.

SFP Socket Status Indicators

Each SFP socket has a status indicator. If the LED is flashing, the link is down.

10/25G Ethernet SFP Socket Link LED Status Indicator

•

Red:

Fault, 3V3 regulator failure.

•

Green:

10G OK

•

Blue:

25G OK

50G Ethernet QSFP+ Socket Link LED Status Indicator

•

Red:

Fault, 3V3 regulator failure.

•

Blue:

50G, 100G OK

SFP 1 to SFP 4

status LEDs

Shows the SFP 1, 2, 3, and 4 link status:

•

Blue:

Link OK (25G/50G/100G SFP).

•

Blue flashing:

SFP detected, link down (fiber not connected,

different FEC selection from host).

•

Unlit:

SFP not detected.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands