GRASS VALLEY IQUCP25 User Manual Download

Page: 194 / 338

194

MADI Processing SDC

Ethernet Pages 1 and 2

Switch LLDP Info

Shows the switch’s Link Layer Discovery Protocol information received

from the switch that the card is connected to.

Name:

Shows the name assigned to the network IP switch.

ID:

Shows the IP switch ID.

Port ID:

Shows the IP switch port ID.

Port VLAN:

Shows the VLAN ID number used by the network

interface.

All Traffic

Shows the Ethernet port’s bandwidth

Capacity

, current data rate

(

Actual

Used %

), and the remaining available (

Free

Click

Enable Stats

to activate.

CPU Traffic

Shows information about traffic going through the card.

Parameter

Description

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands