GRASS VALLEY IQUCP25 User Manual Download | Manualshive

Page: 22 / 338

background image

22

Introduction

Supported SFP28 Cartridges for UCP

-

3901

Supported SFP28 Cartridges for UCP

-

3901

Up to four SFP28 cartridges are required (extra). These are shipped as a separate order. To

support 50G bandwidth requires 4 × 25G SFPs.

SFP Model

Selection

Description

SFP-ETH10G-RT-

M85-LC

Short range optical 10GBase Ethernet SFP cartridge with LC/PC fiber

connector:
• <300m link with OM3 MMF.
• <82m link with OM2 MMF.
• <33m link with OM1 MMF.
850 nm multi-mode optical transceiver that supports signals up to

10.5 Gb/s for bidirectional serial data communications such as

10GBASE-SR and 10GBASE-SW.

SFP-ETH10G-RT-

S13-LC

Long range optical 10GBase Ethernet SFP cartridge with LC/PC fiber

connector (<10 000m):
1310 nm single mode optical transceiver that supports signals up to

10.5 Gb/s for bidirectional serial data communications such as

10GBASE-LR and 10GBASE-LW.

SFP-25-SR

Short range SFP28 25GBASE Optical Transceiver MMF cartridge

(<300m).

SFP-25-LR

Long range SFP28 25GBASE Optical Transceiver SMF cartridge

(<10 000m).

«
...
20
21
22
23
24
...
»

Summary of Contents for IQUCP25



















































































































































































































































































































































Reviews:

No comments

Related manuals for IQUCP25

Brand: Aastra Pages: 2

Brand: Cabletron Systems Pages: 21

Brand: Yamaha Pages: 4

Brand: Keithley Pages: 59

Brand: M86 Security Pages: 46

Brand: NEC Pages: 6

Brand: VMIC Pages: 126

MultiConnect SE MTS2EA

Brand: Multitech Pages: 8

Brand: Barco Pages: 30

Thin Client US310e

Brand: NEC Pages: 6

Brand: Cisco MERAKI Pages: 4

Brand: MFJ Pages: 11

Brand: Lindy Pages: 12

Brand: Cypress Semiconductor Pages: 31

Brand: Digi Pages: 75

Ultra WiFi Booster

Brand: Optus Pages: 8

Emulation Memory Board R0E330850MSRC0

Brand: Renesas Pages: 4

Brand: Cypress Semiconductor Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands