GRASS VALLEY IQUCP25 User Manual Download

Page: 124 / 338

124

Essence Processing SDC

Input Spigots

Streaming

Set the redundancy options for this spigot. This will also determine

the bandwidth to be used. Options are:

•

Dual:

Full redundancy to support SMPTE ST 2022-7, both Primary

(

SFP1

) and Secondary (

SFP2

) Ethernet connectors are used.

Bandwidth is split between the Primary and Secondary. See

Cabling to Support SMPTE ST 2022

on page 55.

To support redundancy, you must set the

Flow Type

to 2110 for

both the primary and secondary ports for the Video, Audio, and

Metadata essences. See below.

•

Single:

Primary Ethernet connector only (

SFP1

), but with all

available bandwidth.

•

Primary Ethernet connector only (

SFP1

•

Secondary Ethernet connector only (

SFP2

•

off:

The stream is disabled.

See

Rear Panel and Connectors

on page 32 for SFP / connector

locations.

Format

Select the format to be used on this spigot. This will ensure that the

appropriate level of bandwidth is allocated for the stream.

Num Audio Flows Select the number of audio flows on this spigot to use. Options are:

• 1 flow of 16 channels
• 2 flows of 8 channels each
• 4 flows of 4 channels each

Note these flows are contiguous, so selecting

means Flow 1 is used,

selecting

means Flows 1 and 2 are used, and selecting

means

Flows 1 to 4 are used.
This setting impacts how Audio Shuffling works. See

Audio Shuffle

page 131 for more information.

Sender / Ext

Headers

Extended header operation can be set for TR-03/TR-04 compatibility.
Extended headers provide in-band metadata regarding the essence

flow and its format, and are applicable to ST-2110 only. If third-party

equipment is unable to support this, the functionality can be

disabled, or set to

On (Legacy)

, which ensures that the packet format

complies with ST2110 but has no video content.
Options are:

Off:

Extended headers are disabled.

On:

Sends extended headers fully compliant with ST2110-20.

On (Legacy):

Sends extended headers only, as with previous versions

of the card.

Sender / Num

Audio Channels
(Multiviewer SDC

only)

Select the actual number of audio channels present on this spigot. Set

the highest number of audio channels expected to be used.

Parameter

Description

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands