GRASS VALLEY IQUCP25 User Manual Download

Page: 150 / 338

150

Essence Processing SDC

Logging - SFP

Logging - SFP

The

Logging SFP

page shows SFP message types relating to fitted SFP modules: Log field

names and current log values are listed in the

Log Field

and

Log Value

columns respectively.

Information on several parameters can be made available to a logging device connected to

the RollCall network. For the UCP-3901, logging must be configured and enabled; see

Logging - Configuration (UCP

3901 Only)

on page 137.

Figure 6 - 32:

Logging - SFP Page

The logging page comprises three columns for each SFP:

Enable check boxes to activate log fields as required.

Logging Page

Column

Description

Log Enable

Select the check boxes that correspond to the parameters for which

log information should be collected.

Log Field

Displays the name of the logging field.

Log Value

Displays the current log value.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands