GRASS VALLEY IQUCP25 User Manual Download | Manualshive

Page: 37 / 338

background image

37

UCP

-

3901

User Manual

• An optional SFP (Small Form-factor Pluggable) module into which the optical fibers are

plugged, and which incorporates the optical/electrical interface.

The optical fibers must be terminated in an LC connector.
In the card’s configuration, SFP1 is identified as Ethernet 1 and SFP2 is identified as Ethernet

2 in the

SFP Configuration

page (see

SFP Configuration

, on page 170).

See

Installing the SFP Ethernet Module

, on page 335 for instructions on installing and

removing the SFP interface module, and for plugging and unplugging the LC-terminated

fibers.
See

Supported SFP28 Cartridges for IQUCP25 / IQUCP50

, on page 26 for the SFP modules

supported by the UCP

-

3901.

«
...
35
36
37
38
39
...
»

Summary of Contents for IQUCP25



















































































































































































































































































































































Reviews:

No comments

Related manuals for IQUCP25

Professional Series

Brand: PACOM Pages: 15

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brand: National Instruments Pages: 85

Brand: SUNRICH TECHNOLOGY Pages: 5

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: ACTi Pages: 12

CNPS11X Extreme

Brand: ZALMAN Pages: 12

Brand: Hauppauge Pages: 62

Brand: Comway Pages: 20

Brand: Dataprobe Pages: 16

Brand: Digital Voice Systems Pages: 32

LITTLE BOARD P5X

Brand: Ampro Corporation Pages: 121

Brand: Planet Pages: 20

Brand: Abocom Pages: 70

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brand: Paradyne Pages: 28

Brand: Altronix Pages: 8

Dablet DVP 5000

Brand: DarbeeVision Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands