GRASS VALLEY IQUCP25 User Manual Download

Page: 323 / 338

323

UCP

3901

MV SDC

Chapter

User Manual

To remove a fan

1 During off hours when the system is not in use, eject the UCP

3901 card from the

Densité frame.

2 Flip the UCP

3901 card over to the non-fan side on an anti-static bag or anti-static mat

so that you can see the rear (solder side) of the card.

3 Using needle-nose pliers, compress the two pushpins so that they unlatch. Push the pin

through the card to release it from the assembly.

4 Flip the card back to the component (fan) side. Insert the pliers under the one of the

pushpin heads. Press down on the center of the fan assembly to prevent it from

flipping on its side and gently pry the pin from the heatsink assembly. Repeat for the

second pushpin.

5 Using curved tweezers, disconnect the fan power connector plug, very carefully; gently

wiggle the connector plug from the socket (jack). Do not pull on the wires. If the wires

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands