GRASS VALLEY IQUCP25 User Manual Download

Page: 196 / 338

196

MADI Processing SDC

Ethernet 1 and 2 RTP Receiver

Ethernet 1 and 2 RTP Receiver

The

RTP Receiver

pages display the amount of data received, details of packet loss, plus

any unwanted multicast traffic on a spigot-by-spigot basis. Units are megabits per second.

Figure 7 - 11:

Ethernet 1 & 2 RTP Receiver Page

Parameter

Description

Enable Stats

Set to display the amount of data received.

Clear RTP Count

Click to zero RTP Sequence Discontinuity counters.

Clear Error Count Click to zero Error counters.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands