GRASS VALLEY IQUCP25 User Manual Download

Page: 121 / 338

121

UCP

3901

User Manual

Spigot Pages

A separate page is provided for each of the active spigots. These pages are dynamically

configured by the product, based on the capabilities of the software version/firmware

selected.

To know on which HD-BNC input / output each spigot is available on the rear panel, see:

• For the UCP

3901:

12G/3G/HD/SD-SDI I/O – Serial digital video inputs / outputs (4)

page 34 and

3G / HD / SD SDI I/O – Serial digital video inputs / outputs (12)

on page 35.

• For the IQUCP25 / IQUCP50:

Images of Rear Panel Connectors

on page 46.

Note:

The pages shown here may differ from those seen on your particular

system, depending on the model and configuration of your UCP

3901

/ IQUCP25 / IQUCP50 card.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands