GRASS VALLEY IQUCP25 User Manual Download

Page: 303 / 338

303

UCP

3901

Multiviewer SDC

Chapter

User Manual

Layout

Select the wall layout to use from the drop-down list.

Layout Transition:
Fade Through

Black

Controls the type of on-screen transition seen when changing

between wall layouts.

• Select for fade down to black, then fade up to new layout.
• Deselect for a cut from current to new wall layout.

Wall Designer

Mode Overlay

Information:

Not supported.

Identify Inputs

Not supported.

Identify Outputs •Not supported.

Table 9-1: Layout and Controls Settings (continued)

Setting

Description

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands