GRASS VALLEY IQUCP25 User Manual Download

Page: 4 / 338

Notices

• Pour plus de sécurité, vérifiez périodiquement la valeur de résistance du bracelet

antistatique. Elle doit se situer entre 1 et 10 mégohms.

• Si vous devez mettre une carte de côté, assurez-vous de la ranger dans un sac

protecteur antistatique.

• Les cartes qui sont reliées à un châssis ou boîtier métallique mis à la terre ne

nécessitent pas de protection antistatique spéciale.

Environmental Information

European (CE) WEEE directive.

This symbol on the product(s) means that at the end of life disposal it should not be mixed

with general waste.
Visit

www.grassvalley.com

for recycling information.

Grass Valley believes this environmental information to be correct but cannot guarantee its

completeness or accuracy since it is based on data received from sources outside our

company. All specifications are subject to change without notice.
If you have questions about Grass Valley environmental and social involvement (WEEE,

RoHS, REACH, etc.), please contact us at

[email protected]

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands