GRASS VALLEY IQUCP25 User Manual Download

Page: 324 / 338

324

Maintenance & Troubleshooting

Replacing the Micro-SD Card

are routed through wire holders, remove the wires from the holders first, before

disconnecting.

6 Dispose of the failed fan assembly.
7 Remove any accumulated dust from the UCP

3901 card with compressed air.

To install the new fan

1 Place the fan assembly on the heatsink and align the two pushpins with their

respective holes on the card.

2 Press down on the fan assembly to hold it in place and press the pushpins into the

holes until they lock into place.

3 Connect the power connector for the replacement fan assembly to the

J14

jack on the

card.

4 Insert the UCP

3901 card into the Densité frame.

5 Put the UCP

3901 into operation and confirm that the critical temperature and fan

alarms are now reported in RollCall as being normal. For this, ensure that:

• The

Fan Status Check

alarm is inactive. See

Logging - System

, on page 140 for

more information. If the

Fan Status Check

alarm is active, ensure the fan is plugged

into Power Connector

J14

• The critical temperature alarm is inactive. See

TEMP_N_STATE=

Logging - FPGA

on page 153 for more information.

Replacing the Micro-SD Card

When the UCP

3901 does not boot, the Micro-SD card must be replaced. Note that using a

blank Micro-SD card will not work. The Micro-SD card must be pre-loaded with firmware

and other files. First call Technical Support to order part number

93-03084-010

. See

Grass

Valley Technical Support

, on page 338.

When replacing a UCP

3901 card for maintenance purposes, you can remove the Micro-SD

card from the old UCP

3901 card and then install it on the new UCP

3901 card. This

transfers the old card’s configuration to the new card so that the replacement UCP

3901

card becomes plug & play with your current installation.

Fan Power Connector Jack J14

Fan Power Connector Plug

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands