Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 22

Page: 22 / 344

6.8 Saving Management and Configuration Information

............................................................................ 194

6.8.1 Saving PSA management information

............................................................................................ 194

6.8.2 Saving MMB configuration information

............................................................................................ 196

6.8.3 Saving BIOS configuration information

........................................................................................... 197

6.9 Configuring Service Life Monitoring by RAS Support Service

.............................................................. 199

6.9.1 BBU service life monitoring for a RAID card

.................................................................................... 199

6.9.2 Battery unit service life monitoring for a UPS

.................................................................................. 201

6.10 Recovery Procedure after the Execution of the Simple Setup Tool (editconf.sh)

............................... 202

CHAPTER 7 Work after Installation

............................................................................................................... 205

7.1 Duplicate Network Adapter Configuration

............................................................................................. 206

7.2 Configuring NTP

................................................................................................................................... 207

7.2.1 How NTP operates in the PRIMEQUEST 1000 series

.................................................................... 207

7.2.2 Setting an NTP server

..................................................................................................................... 208

7.3 Configuring a DNS Server

.................................................................................................................... 211

7.4 Configuring SMTP

................................................................................................................................ 212

7.5 Configuring Security

............................................................................................................................. 213

7.5.1 Configuring access control

.............................................................................................................. 213

7.5.2 Configuring SNMP

........................................................................................................................... 216

7.5.3 Configuring SSH

.............................................................................................................................. 219

7.5.4 Configuring HTTPS

......................................................................................................................... 220

7.6 Scheduled Operations

.......................................................................................................................... 222

CHAPTER 8 Powering On and Off a Partition

............................................................................................... 223

8.1 Powering On and Off a Partition

........................................................................................................... 224

8.1.1 Powering on a partition

.................................................................................................................... 224

8.1.2 Powering off a partition

.................................................................................................................... 225

APPENDIX A Lists of Settings (Links)

........................................................................................................... 227

A.1 MMB Settings

....................................................................................................................................... 228

A.2 PSA Settings

........................................................................................................................................ 229

A.3 UEFI Settings

....................................................................................................................................... 230

A.4 BMC Settings

....................................................................................................................................... 231

APPENDIX B Manual PSA Installation and Uninstallation

............................................................................. 233

B.1 Manually Installing PSA (Linux: Red Hat Enterprise Linux)

................................................................. 234

B.1.1 Installation flow

................................................................................................................................ 234

B.1.2 Checks before PSA installation

....................................................................................................... 234

B.1.3 Installing PSA

.................................................................................................................................. 237

B.1.4 Automatic configuration during PSA installation

............................................................................. 237

B.1.5 Restarting the partition

.................................................................................................................... 238

B.1.6 Settings after PSA installation

......................................................................................................... 238

B.1.7 Installing a PSA update

................................................................................................................... 242

B.1.8 Uninstalling PSA

............................................................................................................................. 242

B.2 Manually Installing PSA (Windows Server 2003)

................................................................................. 243

B.2.1 Installation flow

................................................................................................................................ 243

B.2.2 Checks before PSA installation

....................................................................................................... 244

B.2.3 Installing PSA

.................................................................................................................................. 245

B.2.4 Automatic configuration during PSA installation

............................................................................. 247

B.2.5 Settings after PSA installation

......................................................................................................... 248

B.2.6 Installing a PSA update

................................................................................................................... 248

B.2.7 Uninstalling PSA

............................................................................................................................. 248

B.3 Manually Installing PSA (Windows Server 2008)

................................................................................. 249

B.3.1 Installation flow

................................................................................................................................ 249

B.3.2 Checks before PSA installation

....................................................................................................... 250

B.3.3 Installing PSA

.................................................................................................................................. 251

B.3.4 Automatic configuration during PSA installation

............................................................................. 254

B.3.5 Settings after PSA installation

......................................................................................................... 255

PRIMEQUEST 1000 Series Installation Manual
Contents

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands