Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 177

Page: 177 / 344

6.3

Configuring PSA (Windows Server 2003)

This section describes confirmation of the required settings for PSA operation after operating system installation,

and corresponding features about the settings.

TABLE 6.7 Confirmation of the required settings for PSA operation, and corresponding features about
the settings

Required/

As needed

Setting item

Automatic setting (*1)/

Manual setting (*2)

See

Required

Configuring the PSA-to-

MMB communication LAN

Manual setting

6.3.1 Configuring the PSA-to-MMB

communication LAN

Confirming management

LAN settings

Manual setting

6.3.2 Confirming management LAN

settings

Configuring the

Windows Firewall

Manual setting

6.3.5 Configuring the Windows

Firewall

Setting the management

LAN IP address

Manual setting

6.3.7 Setting the management LAN

IP address

As needed

Setting the destinations of

traps from a partition

Manual setting

6.3.3 Setting the destinations of traps

from a partition

Setting the destinations of

traps and e-mail via the

MMB

Manual setting

6.3.4 Setting the destinations of traps

and e-mail via the MMB

Setting Watchdog for

monitoring after a STOP

error (fatal system error)

Manual setting

6.3.6 Setting the Watchdog Timer

for monitoring after a STOP error

(fatal system error)

Installing a PSA update

Not applicable

6.3.8 Installing a PSA update

Uninstalling PSA (*3)

Not applicable

6.3.9 Uninstalling PSA

*1 Automatic setting: Values are automatically set during PSA installation. You may need to change an

automatically set value. See the section listed in the table.

*2 Manual setting: Values are not automatically set during PSA installation. Make settings as described in the

section referred to in the table.

*3 To operate the PRIMEQUEST 1800E server, you need to first install PSA. Otherwise, the following restrictions

apply.

- I/O (e.g., PCI Express card, hard disk) failure notification and trap notification to the administrator are

disabled.

- Failure notification using symptom detection and trap notification to the administrator are disabled.

- Threshold exceeded in S.M.A.R.T. monitoring of HDDs

- Operations management software cannot collect information on the partition side.

- Even under an REMCS agreement, no software errors are reported.

Remarks

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

149

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands