Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 180

Page: 180 / 344

[PSA installation folder]\opt\FJSVpsa\sh\setpsalan.bat

Note

If the operating system has not been restarted after PSA installation, the PSA-to-MMB communication LAN

setting command in step 1 will fail.

Execute the PSA-to-MMB communication LAN setting command after restarting the operating system.

2. Restart the operating system.

Performing the above procedure sets the following values.

172.30.0.<

partition ID

+ 2>/24

Example: Partition ID of 2

172.30.0.4/24

Auto Negotiation off

Speed 100 Mbps

Duplex full

In the following cases, change the IP addresse setting.

- The automatically set IP address is the same as the IP address or subnet used for a production network or

management network.

- You are configuring a new partition using a duplicate disk from another partition.

- The partition ID changes because a disk installed in a partition was moved to another partition.

- You are configuring a Windows cluster (MSCS) with partitions assigned the same number, with the cluster

spanning cabinets. (The same IP addresses are assigned, so a configuration check detects an error indicating

that a duplicate IP address was found.)

Change the IP address setting by using the following procedure. If you are changing the setting because of the above

reason 1, you need to change the IP addresses of all partitions in the cabinet and the IP address of the PSA-to-MMB

communication LAN on the MMB side to IP addresses in the same subnet. Change the IP addresses on the MMB

side from the MMB Web-UI.

Notes

- Do not change the automatically set communication values. Otherwise, PSA-MMB communication may be

disabled, making PSA functions unavailable.

- Change PSA-to-MMB LAN settings only after PSA installation. If changed before PSA installation, the

settings are overwritten by the installation.

Configuring the network adapter for the PSA-to-MMB communication LAN

Configure the network adapter by using the following procedure.

Operations

1. Select [Control Panel] - [Network Connections].

>> A window displays a list of networks.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

152

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands