Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 298

Page: 298 / 344

E.4

Settings after VMware 4.x PSA Installation

The settings after PSA installation for VMware 4.x partly differ from those for RHEL. This section describes only

the different parts.

For details on the parts of the setting procedure that are the same as those for RHEL, see the following.

TABLE E.1 Settings after PSA Installation (VMware 4.x)

Settings after PSA installation

For VMware 4.x

Configuring the PSA-to-MMB communication

LAN

E.4.1 Configuring the network

Confirming management LAN settings

E.4.1 Configuring the network

Confirming SELinux function settings

(No settings required)

Confirming the firewall function

E.4.2 Configuring the firewall

Setting the destinations of traps from a partition

Same as for RHEL

6.2.5 Setting the destinations of traps from a partition

Setting the destinations of traps and e-mail via

the MMB

Same as for RHEL

6.2.6 Setting the destinations of traps and e-mail via the

MMB

Setting the management LAN IP address

Same as for RHEL

6.2.7 Setting the management LAN IP address

Configuring SNMP to use duplicate disks

Same as for RHEL

6.2.8 Configuring SNMP to use duplicate disks

Configuring the default gateway

E.4.3 Configuring the default gateway

Remarks

PSA is provided only with the PRIMEQUEST 1800E.

All screenshots are display examples, and the actually displayed contents vary depending on the system

configuration and other factors.

E.4.1

Configuring the network

This section describes the network settings required to install and operate PSA.

Use the following workflow to perform the work.

Confirming the PSA-to-MMB communication LAN and management LAN

Configuring the management LAN

Configuring the PSA-to-MMB communication LAN

Usually, the network is configured as shown below immediately after the installation of the operating system.

The interface name, BUS number, and other names must be replaced with suitable character strings according to

the environment.

PRIMEQUEST 1000 Series Installation Manual
APPENDIX E Notes on VMware Installation

270

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands