Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 42

Page: 42 / 344

2.9

Connecting the Power Cables

This section describes how to connect the power cables.

The main unit and PCI_Box are shipped with (three-wire) power cables equipped with a grounded plug. You need

to connect the power cables to outlets with ground terminals.

Remarks

The main unit and PCI_Box are designed to operate with a power supply facility that supports grounded wiring.

Do not connect the main unit and PCI_Box to a power supply facility that does not provide grounded wiring. To

determine the type of power supply in your building, contact the building manager or a qualified electrical engineer.

Operations

1. Confirm with an on-site electrical engineer that the input power satisfies power requirements. For details on

the power requirements, see 1.3 Installation Specifications in the

PRIMEQUEST 1000 Series Hardware

Installation Manual

(C122-H004EN).

2. Confirm that the power cables are connected to the AC inlets of the main unit and PCI_Box. Also confirm

that the power cables are secured with the AC cord clamps for the AC inlets on the main unit.

3. Group all the cables that run outside the main unit and PCI_Box into power cables and signal cables, and

secure them firmly to the cable holders of the 19-inch rack with cable ties.

4. Confirm that the AC power breaker is off. Then, connect the power cables to AC power. For details on the

power cable connections, see

2.4.2 Facility power requirements and characteristics

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 2 Preparing for Main Unit Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands