Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 117

Page: 117 / 344

Remarks

You can confirm a trap destination setting by using the standard trap of the SNMP service. (See

How to

confirm a trap destination setting

6.3.3 Setting the destinations of traps from a partition

7. Set the destinations of SNMP trap and e-mail via the MMB.

Make settings only as needed, such as for linkage with operations management software.

1. Display the [SNMP Configuration] menu in the MMB window, and enable SNMP.

2. Set the destinations of SNMP traps via the MMB.

(See

7.5.2 Configuring SNMP

8. Configure the firewall.

For Windows Server 2003: See

6.3.5 Configuring the Windows Firewall

For Windows Server 2008: See

6.4.6 Configuring the Windows Firewall

For Windows Server 2012: See the

ServerView Mission Critical Option User Manual

9. Set the Watchdog Timer for monitoring after a STOP error. For details, see

6.3.6 Setting the Watchdog Timer

for monitoring after a STOP error (fatal system error)

1. Edit the PSA configuration file [pnwatchdog.conf].

2. Set the following key values:

Section: [WATCHDOG]

Key: [TIMER]

Setting value (unit: seconds): 0 (Watchdog Timer disabled), 1 to 6000 (Watchdog Timer monitoring

time)

10. Set the management LAN IP address.

Make this setting only if you need to change the management LAN IP address. For details, see

6.3.7 Setting

the management LAN IP address

11. Install updates of PSA and other bundled software.

Check the latest versions of the software at their download sites, and install the necessary updates. For details

on PSA, see

6.3.8 Installing a PSA update

12. Configure the dump area.

Confirm that the hard disk has enough free space before collecting a memory dump. For details, see 11.4.4

Setting up the dump environment (Windows) in the

PRIMEQUEST 1000 Series Administration

Manual

(C122-E108EN).

13. Configure the NTP client.

Configure the NTP server on the operating system side. For details, see

7.2 Configuring NTP

14. Save management and configuration information. For details, see

6.8 Saving Management and Configuration

Information

15. Configure RAS Support Service. For details, see

6.9 Configuring Service Life Monitoring by RAS Support

Service

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands