Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 4

Page: 4 / 344

Organization of this manual

This manual is organized as follows.

CHAPTER 1 Installation Overview

Chapter 1 describes the workflow up to actual operation of the PRIMEQUEST 1000 series server.

CHAPTER 2 Preparing for Main Unit Installation

Chapter 2 describes the preparation before main unit installation. This preparation includes work up to power

cable connection.

CHAPTER 3 Work before Operating System Installation

Chapter 3 describes the work that must be done before you install an operating system on the PRIMEQUEST

1000 series server. The chapter also describes settings for actual operation and various setup work.

CHAPTER 4 Installing the Operating System and Bundled Software

Chapter 4 describes how to install the operating system and bundled software.

CHAPTER 5 Work after Operating System Installation (PRIMEQUEST 1800E2)

Chapter 5 describes how to make various necessary settings after operating system installation on the

PRIMEQUEST 1800E2.

CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

Chapter 6 describes how to make PSA and various other necessary settings after operating system installation

on the PRIMEQUEST 1800E.

CHAPTER 7 Work after Installation

Chapter 6 describes the work performed after PRIMEQUEST 1000 series installation. This work includes

configuring NTP and security.

CHAPTER 8 Powering On and Off a Partition

Chapter 7 describes partition power control.

APPENDIX A Lists of Settings (Links)

Appendix A provides links to Appendix A List of Settings in the

PRIMEQUEST 1000 Series Tool

Reference

(C122-E110EN).

APPENDIX B Manual PSA Installation and Uninstallation

Appendix B describes how to manually install and uninstall PSA for a specific operating system.

APPENDIX C Software (Links)

Appendix C provides a link to 3.3 Bundled Software in the

PRIMEQUEST 1000 Series General

Description

(C122-B022EN).

APPENDIX D Configuring the SAN Boot Environment

Appendix D is a link to the

PRIMEQUEST 1000 Series SAN Boot Environment Configuration Manual

(C122-

E155EN).

APPENDIX E Notes on VMware Installation

Appendix E describes the procedure for installing a built-in hard disk in a RAID environment in VMware

vSphere and provides notes on installation.

APPENDIX F Setting up the NTP Server (Windows)

Appendix G describes how to specify and set of an NTP server for a specific Windows operating system.

PRIMEQUEST 1000 Series Installation Manual
Preface

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands