Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 152

Page: 152 / 344

- After moving a monitored RAID card to another partition through a partition configuration change, you need

to correct the RAS Support Service settings. First, in the Mounting Dates list, clear the RAID card mounting

date on the original source partition. Then, set the RAID card mounting date on the destination partition.

FIGURE 5.4 RAS Support Service screens (move to another partition)

- The PRIMEQUEST 1800E2 can have multiple partition configurations.

For example, suppose a partition requires many CPUs during the day and a lot of I/O at night, the partition

configuration must change between day and night. This means changes in the SB and IOB connection

configuration.

In this case, to move a RAID card to another partition, determine the primary partition for service life

monitoring and then set the partition in RAS Support Service.

If both partitions are set by mistake, notifications from both partitions will be issued in service life monitoring

for the same RAID card.

5.7.2

Battery unit service life monitoring for a UPS

The battery unit on a UPS is a service life component. RAS Support Service performs service life monitoring.

RAS Support Service sends messages for replacement notification at the following times.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 5 Work after Operating System Installation (PRIMEQUEST 1800E2)

124

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands