Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 39

Page: 39 / 344

2.6

Preparing to Install the Main Unit

TABLE 2.1 Accessories required in main unit installation

lists the accessories required in main unit installation.

Prepare these accessories in advance.

TABLE 2.1 Accessories required in main unit installation

Accessory name

Description

No. 2 Phillips screwdriver

Used to mount the unit in a rack.

Wrist strap

Used to prevent main unit damage from static electricity discharged from

your body.

Conductive mat

Required for some system configurations. To order any of the accessories,

contact the distributor where you purchased your product, or your sales

representative.

Ethernet Category 5 cable or better

Console PC-to-LAN cable (for user

LAN)

External switching hub

Used to connect the PRIMEQUEST 1000 series server to an external

switching hub via a LAN.

Multitester

Used to check the input AC voltage.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 2 Preparing for Main Unit Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands