Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 46

Page: 46 / 344

3.1

Before Starting Setup

This section describes the decisions that must be made before you start setup.

3.1.1

MMB settings

You need to decide the following to configure the MMB:

- IP address, host name, subnet mask, and gateway address

- IP address of the PC used as the MMB console (referred to below as the MMB console PC)

- User accounts

- Name of the PRIMEQUEST 1000 series system (also used as the SNMP system name)

- Management LAN environment ... etc.

For details on MMB settings, see

3.3 Connecting and Configuring the MMB

Note

The management LAN, PSA-to-MMB communication LAN, and remote maintenance LAN must be configured as

networks with different subnet masks.

3.1.2

Partition settings

You need to decide the following before using the partitioning functions to configure multiple partitions:

- Number of partitions

- Partition names

- Partition configuration

- Home SB

For details on partition settings, see

3.4 Configuring a Partition

Remarks

If each partition has the same name as the host name of the operating system installed on the partition, partition

management is easier.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands