Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 136

Page: 136 / 344

Remark

The IP address of the LAN cannot be set through the operating system setup. Set the IP address after the

installation of the operating system.

7. Click [Install].

Installationbegins.

8. Replace the media with the operating system installation media according to the SVIM instructions.

4.10.4

Configuring bundled software after the completion of installation

After completing OS installation, configure the bundled software.

For details about the following settings, see the

ServerView Mission Critical Option User Manual

1. Configure the PSA-to-MMB communication LAN network.

For details, see the items in "Configuring the PSA-to-MMB communication LAN."

2. Configure the management LAN network.

For details, see the items in "Confirming management LAN settings."

3. Install the SVmco package.

For details, see the items in "Installing SVmco."

4. Make manual settings in the SVmco configuration file.

For details, see "Configuring SVmco."

5. Check the firewall function.

For details, see the items in "Checking the firewall function (opening ports)."

Open the following ports for use with the PSA-to-MMB communication LAN interface.

TABLE 4.12 Ports to open for the PSA-to-MMB communication LAN interface

Port

Port number

Sending / Receiving

snmp port

udp/snmp or 161

For sending and receiving

psa-mmb

communication port

tcp/5000

For sending and receiving

icmp/icmp-type0, icmp-type8

6. Restart the partition.

For details, see the items in "Restarting the partition."

7. After installing SVmco, make the required settings.

Set the management LAN parameters.

For details, see the items in "Settings after SVmco installation."

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

108

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands