Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 342

Page: 342 / 344

[L]

Lists of Settings (Links).................................................

[M]

Maintenance status display...............................................

[Management LAN Port Configuration] window (example)
..........................................................................................

Manually Installing PSA (Linux: Red Hat Enterprise Linux)
........................................................................................

234

Manually Installing PSA (Windows Server 2003).........

243

Manually Installing PSA (Windows Server 2008).........

249

Manual PSA Installation and Uninstallation..................

233

Message for advance notification of replacement and
replacement notification message (RAID card)....

123

199

Message for advance notification of replacement and
replacement notification message (UPS)..............

125

201

MMB connection and configuration flow........................

MMB Settings................................................................

228

MMB USER port location................................................

MMB Web-UI login window...........................................

[Mode] window (example).................................

Mounting location and external interfaces of the MMB....

Mounting the Main Unit in a 19-inch Rack.....................

[N]

Network configuration after setup..................................

276

Network configuration and IP addresses of the management
LAN..................................................................................

Network configuration immediately after installation of OS
........................................................................................

271

[Network Interface] window (example)....................

[Network Protocols] window (example)....

216

220

221

New Inbound Rule Wizard - Action..............................

177

New Inbound Rule Wizard - Name................................

179

New Inbound Rule Wizard - Profile..............................

178

New Inbound Rule Wizard - Program............................

174

New Inbound Rule Wizard - Protocol and Ports............

175

New Inbound Rule Wizard - Rule Type.........................

173

New Inbound Rule Wizard - Scope................................

176

New Outbound Rule Wizard - Protocol and Ports....

180

182

Notes on VMware 4.x Installation.................................

262

Notes on VMware Installation.......................................

260

NTP Settings in Windows Server 2003..........................

286

NTP Settings in Windows Server 2008..........................

289

NTP Settings in Windows Server 2008 R2....................

295

NTP Settings in Windows Server 2012..........................

303

[O]

Operating system installation by SVIM....

102

106

110

Operation with external NTP servers (three NTP servers)....

208

Overview of NTP Client Settings...................................

284

[P]

Packages required for PSA operation (RHEL5)............

235

Packages required for PSA operation (RHEL6)............

235

Packages required for SIRMS operation (RHEL6)........

236

[Partition Configuration] window (example).....

[Partition Home] window (example)................................

Ports to open for the management LAN interfaces........

135

Ports to open for the PSA-to-MMB communication LAN
interface.................................................................

108

113

Ports to open for the PSA-to-MMB communication LAN
interfaces........................................................................

139

Power cable socket locations (PCI_Box).........................

Power cable socket locations (PRIMEQUEST
1800E2/1800E).................................................................

[Power Control] window (example)......................

224

226

Powering On and Off a Partition...........................

223

224

Preparing for Main Unit Installation..................................

Preparing the Power Supply Equipment............................

Preparing to Install the Main Unit....................................

Preparing to Install window.......

[Program and Features] window....................................

188

Program removal window..............................................

187

[Properties] dialog box.................................

294

301

310

[Protocol and Ports] setting items.........................

174

180

PSA Settings...................................................................

229

[R]

RAS Support Service screens (move to another partition)....

124

200

RAS Support Service screens (no BBU)...............

123

200

Recovery Procedure after the Execution of the Simple Setup
Tool (editconf.sh)...........................................................

202

[Registry Editor] selection window................................

305

[Registry Editor] window....................

[Remove SB/IOB/GSPB from Partition] window (example)
..........................................................................................

Required settings for external LAN connections.............

[Reserved SB Configuration] window (example)............

RHEL Installation Procedures on the SAN Storage Unit....

[Run] window...............................................

287

290

296

[S]

Safety Precautions..............................................................

Saving Configuration Information...................................

Saving Management and Configuration Information....

121

194

Scheduled Operations.....................................................

222

[Scope] setting items....................................

175

180

182

[Scope] tab in [SNMP Service (UDP In) Properties].....

171

secLevel settings............................................................

142

Select Features window................................

246

251

253

[Select User or Group] window...................

294

301

311

[Server Configuration] window.....................................

263

[Services] window...............................

Settings after PSA Installation (VMware 4.x)...............

270

Settings after VMware 4.x PSA Installation..................

270

Settings after VMware 4.x SVmco Installation.............

280

PRIMEQUEST 1000 Series Installation Manual
Index

314

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands