Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 121

Page: 121 / 344

6. Set the IP address of the PSA-to-MMB communication LAN in the PSA configuration file.

4. Configure the firewall. For details, see

E.4.2 Configuring the firewall

5. Configure the default gateway. For details, see

E.4.3 Configuring the default gateway

6. Retrieve VMware PSA maintenance information. For details, see

E.4.4 Retrieving VMware 4.x PSA

maintenance information

7. Install updates of PSA and other bundled software.

Check the latest versions of the software at their download sites, and install the necessary updates. For details

on PSA, see

6.2.9 Installing a PSA update

4.6.6

Configuring a software watchdog

Remarks

If you use SVOM 5.0, see

When using SVOM 5.0 or later

E.2 Notes on VMware 4.x Installation

1. Start ServerView Operations Manager.

2. Select [ServerList].

3. Right-click the target partition in the server list on the left side. Select [Maintenance] - [ASR Properties] from

the displayed menu.

4. Select [Watchdog] in the displayed window.

5. Specify the following for [Software], and click [Apply].

- Check the [Active] check box.

- Select [Continue] for [Action] for cases of abnormal operation.

- Enter a value between 1 and 100 minutes for [Timeout].

6. Enter your user name and password, and press the [Enter] key.

4.6.7

Completing VMware 4.x installation

After completing the settings, reboot the partition of the PRIMEQUEST 1000 series server.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands