Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 159

Page: 159 / 344

The PSA-to-MMB communication LAN is usually set with the following values during PSA installation.

172.30.0.<

partition ID

+ 2>/24

Example: Partition ID of 2

172.30.0.4/24

Auto Negotiation off

Speed 100 Mbps

Duplex full

In the following cases, change the IP address setting.

1. The automatically set IP address is the same as the IP address or subnet used for a production network or

management network.

2. You are configuring a new partition using a duplicate disk from another partition.

3. The partition ID changes because a disk installed in a partition was moved to another partition.

Change the IP address setting by using the following procedure. If you are changing the setting because of the above

reason 1, you need to change the IP addresses of all partitions in the cabinet and the IP address of the PSA-to-MMB

communication LAN on the MMB side to IP addresses in the same subnet. Change the IP addresses on the MMB

side from the MMB Web-UI.

Notes

- Do not change the automatically set communication values. Otherwise, PSA-MMB communication may be

disabled, making PSA functions unavailable.

- Change PSA-to-MMB LAN settings only after PSA installation. If changed before PSA installation, the

settings are overwritten by the installation.

- If [Interface] of [MMB-PSA IP Address] in the [Network Configuration] - [Network Interface] window of

the MMB Web-UI is Disable, you can use neither the screen display nor event notification function of PSA.

After changing it from Disable to Enable, the OS must be restarted.

Confirming the NIC of the PSA-to-MMB communication LAN

Confirm the interface name assigned to the NIC of the PSA-to-MMB communication LAN by using the following

procedure.

Operations

1. Execute the ifconfig command to confirm the interface name. This command lists the network interfaces

recognized by the system.

Syntax

/sbin/ifconfig -a

Example of output

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

131

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands