Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 55

Page: 55 / 344

Password

Password that was set by a field engineer during device setup

Logging out

Click the [Logout] button at the top right in the browser window.

>> You are logged out from the Web-UI.

3.3.5

How to view the Web-UI window

This section describes the information displayed in the Web-UI window.

Remarks

If the Web-UI window displays "Read Error," check for details on the error in 11.2 Troubleshooting in the

PRIMEQUEST 1000 Series Administration Manual

(C122-E108EN). If you cannot solve the problem even after

referring to the manual, contact your sales representative or a field engineer.

Before making contact, confirm the model name and serial number shown on the label affixed to the main unit.

FIGURE 3.5 Information displayed in the window

shows the information displayed in the window.

No.

Description

(1)

Fujitsu logo (link to Fujitsu's top page)

(2)

Navigation bar

(3)

Submenu breadcrumb trail

(4)

Maintenance status display

(5)

Active MMB display

FIGURE 3.5 Information displayed in the window

The information area always displays the following information.

Model

This field displays the model name of the PRIMEQUEST 1000 series server.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands