Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 312

Page: 312 / 344

F.1

Overview of NTP Client Settings

This appendix describes procedures for settings synchronizing the system clock with an NTP server for operating

systems consisting of the following:

- Windows Server 2003/Windows Server 2003 R2

The setup steps do not distinguish between Windows Server 2003 and Windows Server 2003 R2. Windows

Server 2003 and Windows Server 2003 R2 are both called "Windows Server 2003" in this manual.

- Windows Server 2008

- Windows Server 2008 R2

- Windows Server 2012

Remarks

This appendix is not needed for Active Directory member servers. Active Directory member servers automatically

synchronize the system clock with the domain controller.

In the PRIMEQUEST 1000 series, the system time of a partition is kept in the Home SB. Therefore, if the Home

SB of a partition is replaced during maintenance or switched by the reserved SB function, the system time of the

partition may become incorrect.

The system clock synchronizes with an NTP server once a week in the default configuration of the Workgroup

environment of Windows.

Before Windows Server 2008, the system clock is synchronized at system startup. However, in Windows Server

2008 R2 or later, it is not synchronized.

Use the following procedures to set the system to synchronize with the system clock.

TABLE F.1 Settings for system clock syncronization

Task name

Task description

Target OS

Specifying an

NTP Server

Specify an NTP server in [Control Panel] - [Date and Time].

Windows Server 2003

Windows Server 2008

Windows Server 2008 R2

Windows Server 2012

Synchronization

Interval Setting

Set the following registry value with the Registry Editor to set a

synchronization interval of 15 minutes:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet

\Services\W32Time\TimeProviders\NtpClient

*There is no line feed in the above registry key.

name: SpecialPollInterval

type: REG_DWORD

value: 900 (decimal)

Windows Server 2003

Windows Server 2008

Windows Server 2008 R2

Windows Server 2012

Startup Settings

of NTP Service

Set the Windows Time service to start automatically in [Computer

Management] - [Services and Applications] - [Services] (only

Windows Server 2008 R2).

Windows Server 2008 R2

Windows Server 2012

PRIMEQUEST 1000 Series Installation Manual
APPENDIX F Setting up the NTP Server (Windows)

284

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands