Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 129

Page: 129 / 344

4.9

VMware 5.x Installation Procedures on the Built-in HDD

This section concisely describes the procedures for installing VMware 5.x on the built-in HDD.

Start this work only after confirming the completion of the connection and configuration of the MMB.

4.9.1

Advance setup

Set up the following as needed.

1. Prepare a server running ServerView Operations Manager.

2. After removing the built-in HDD of the PRIMEQUEST server, confirm the partition settings with the MMB.

- Setting the SB/IOB/GSPB configuration

(See

3.4.1 Setting a partition configuration

- Configuring Console Redirection

(See

3.4.6 Configuring Console Redirection

- Video redirection: Enable

- Remote storage: Enable

- Console redirection: Enable

- Setting various modes

(See

3.4.5 Setting various modes

3. Assign I/O spaces to the SAS card, SAS array controller card, Onboard SAS controller (GSPB), SAS disk

unit controller and SAS array disk unit controller.

For details on I/O space assignment, see 3.4.5 Setting various modes in this manual and 5.5.1 [Configure I/

O Space Assignment] menu in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

4.9.2

Preparing for Installation

To prepare for installation, also see the VMware information.

For the VMware information, contact the distributor where you purchased your product, or your sales representative.

Prepare the following.

1. Prepare the following disk image:

VMware 5.x media

2. Disconnect all the FC cables.

3. Mount the disk image through a video redirection connection.

4. Configure the RAID environment.

For details, see the MegaRAID SAS Software, the MegaRAID SAS Device Driver Installation, or the LSI

MegaRAID (R) SAS Software contained on the SVS DVD.

5. Change the boot order to give the highest priority in startup to DVD boot.

For details, see 1.3.1 [Power Control] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-

E110EN).

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

101

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands