Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 175

Page: 175 / 344

#vi /var/net-snmp/snmpd.conf

oldEngineID 0x19760523

6. Execute the service command to start snmpd.

Syntax

/sbin/service snmpd start

7. Move to the /opt/FJSVpsa/sh/ directory to generate another SNMPv3 password for internal PSA

communication.

Syntax

cd /opt/FJSVpsa/sh/

8. Execute snmpsetup.sh in this directory.

When executed, snmpsetup.sh automatically generates an SNMPv3 password for internal PSA

communication.

Syntax

./snmpsetup.sh install

9. Start PSA.

Syntax

/sbin/service y30FJSVpsa start

6.2.9

Installing a PSA update

This section describes how to install a PSA update in Red Hat Enterprise Linux.

Execute the following commands in the order shown to first stop PSA services and then install the PSA package

to update PSA.

The following description assumes that the work directory (in the example below, $WORK_DIR) has the PSA

package (FJSVpsa-$VER-$REL.tar.gz) already mapped.

Syntax

/sbin/service y30FJSVpsa stop

cd $WORK_DIR/FJSVpsa

./INSTALL.sh

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

147

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands