Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 278

Page: 278 / 344

You can use the above registry key to specify the wait time (ms) before the service is terminated in the

shutdown sequence.

- The event log may have the following message recorded during PSA startup. It does not indicate any

operational problem.

"PM child process abnormal end [6:750] (tagt) 1:0x00000000"

FJSVpsa Event ID 62

B.3.2

Checks before PSA installation

This section describes the checks to make before PSA installation.

Confirming PSA-to-MMB communication LAN settings

Confirming the services required for PSA operation

Confirming PSA-to-MMB communication LAN settings

For details on how to configure the PSA-to-MMB communication LAN, see

6.4.1 Configuring the PSA-to-MMB

communication LAN

Confirming the services required for PSA operation

SNMP Service is required for PSA operation. Add SNMP Service by using the following procedure.

Operations

1. Click [Start] - [Administrative Tools] - [Server Manager].

2. Select [Features] - [Add Function] - [SNMP Service] in the [Server Manager] window.

3. Confirm that the [SNMP Service] check box is checked. Then, click the [OK] button.

The screen returns to the Windows Component Wizard.

Remarks

If the check box is not checked, SNMP Service has not been installed. To install SNMP Service, check the

check box.

Click the [Next] button in the Windows Component Wizard window. Follow the instructions of the wizard

for installation.

PRIMEQUEST 1000 Series Installation Manual
APPENDIX B Manual PSA Installation and Uninstallation

250

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands